CCNA2 SRWE Module 1 - Basic Device Configuration

Home
Date Subject Lesson Plan
08/25/22 CCNA2

Bellwork: Subnet Practice - 5 points
192.168.3.0 Solve for 8 subnets

School forms - 25 extra credit points

Certifications!! CCNA, A+, Network+, and IC3. Also: MOS

End-of-Semester Pre-Employability Assessment - Improve this year!

Start Chapter 1 -

1.0: Introduction

Read Section: 1.01 Why should I take this module?

Read Section: 1.02 What will I learn to do in this module?

Video: 1.0.3 Download and Install Packet Tracer

PT: 1.0.4 Logical and Physical Mode Exploration

Discussion: Chapter 1 Tour

Read: Section 1.1.1 Configure a Switch with Initial Settings
Video: 1.1.1 Switch Boot Sequence (2:45)
Notes: 1.1.1 Switch Boot Sequence

  1. POST
  2. Boot Loader inializes CPU, memory, flash
  3. Boot Loader locates and loads IOS into memory

Read Section: 1.1.2 The boot System Command
Video: 1.1.2 The boot system Command (2:37)

Read: Section 1.1.3 Switch LED Indicators
Video: 1.1.3 Switch LED Indicators (4:35)
Video: Port LEDs on Cisco Catalyst Switches (5:29)

Read Section: 1.1.4 Recovering from a System Crash
Video: 1.1.4 Recovering from a System Crash (3:32)

Read Section: 1.1.5 Switch Management Access
Video: 1.1.5 Switch Management Access (1:07)
Make sure you understand this! You'll need it later.

Read Section: 1.1.6 Switch SVI Configuration Example
Video: 1.1.6 Switch SVI Configuration Example (2:44)

Video: 1.1.7 Basic Switch Configuration Instructions (0:57)

Lab: 1.1.7 Basic Switch Configuration (Start)

Assignment: Study Guide questions 1-12

Once we complete a section, there can always be a quiz on the material that we covered.

  A+

None today

08/26/22 CCNA2

School forms - 25 extra credit points (last chance)

Lockdown Drill 12:00 (2022)

Subnet Practice - Class C
192.168.3.0 Solve for useable 16 hosts

Lab: 1.1.7 (Finish)

Start Chapter 1, Section 2 - Configure Switch Ports

Read Section: 1.2.1 Duplex Communication
Video: 1.2.1 Duplex Communication (2:32)

Read Section: 1.2.2 Configure Switch Ports at the Physical Layer
Video: 1.2.2 Configure Switch Ports at the Physical Layer (1:43)

Read Section: 1.2.3 Auto-MDIX
Video: 1.2.3 Auto-MDIX (3:16)

Read Section: 1.2.4 Switch Verification Commands
Video: 1.2.4 Switch Verification Commands (0:36)

Read Section: 1.2.5 Verify Switch Port Configuration

Read Section: 1.2.6 Network Access Layer Issues
Video: 1.2.6 Network Access Layer Issues (0:37)

Read Section: 1.2.7 Interface Input and Output Errors

Read Section: 1.2.8 Troubleshooting Network Access Layer Issues

Activity: 1.2.9 Syntax Checker - Configure Switch Ports
Video: 1.2.9 Syntax Checker - Configure Switch Ports (1:15)

Assignment: Chapter 1 Study Guide 13-25

  A+ Software None today
08/29/22 CCNA2
v7.0

Subnet Class B:
190.16.0.0 - Solve for 16 subnets

Start Chapter 1, Section 3 - Secure Remote Access

Read Section: 1.3.1 Telnet Operation
Video: 1.3.1 Telnet Operation (1:18)

Read Section: 1.3.2 SSH Operation

Read Section: 1.3.3 Verify the Switch Supports SSH
Video: 1.3.3 Verify the Switch Supports SSH (1:00)

Read Section: 1.3.4 Configure SSH
Video: 1.3.4 Configure SSH (4:02)

Read Section: 1.3.5 Verify SSH is Operational
Video: 1.3.5 Verify SSH is Operational

PT: 1.3.6 Configure SSH

Assignment: Module 1 Study Guide 26-31

  A+ Software
v7.0

Read Section: 10.0.1.1 Windows Installation Introduction

Read Section: 10.1.1.1

  • Multi-user
  • Multitasking
  • Multiprocessing
  • Multithreading

Read Section: 10.1.1.2 Basic Functions of an Operating System

Read Section: 10.1.1.3 Windows Operating Systems

Practice IM: 10.1.1.4 Check Your Understanding - Windows Terminology

 

08/30/22 CCNA2
v7.0

Activity: Handbook Presentation 11:45 (2022)

Start Chapter 1 - Section 4 Basic Router Settings

Read Section: 1.4.1 Configure Basic Router Settings
Video: Basic Router Configuration (14:03)

Activity: 1.4.2 Syntax Checker - Configure Basic Router Settings

Read Section: 1.4.3 Dual Stack Topology
Video: Transition to IPv6 - Dual Stack (1:57)

Read Section: 1.4.4 Configure Router Interfaces

Activity: 1.4.5 Syntax Checker - Configure Router Interfaces

Read Section: 1.4.6 IPv4 Loopback Interfaces
Video: Cisco Loopback Interfaces Tutorial (9:10)

PT: 1.4.7 Configure Router Interfaces

Assignment: Module 1 Study Guide 32-35

  A+ Software
v7.0

Read Section: 10.1.2.1 Compatible System Software and Hardware Requirements

Read Section: 10.1.2.2 Minimum Hardware Requirements and Compatibility with OS
Video: 10.1.2.2 Minimum Hardware Requirements and Compatibility with OS (1:04)

Read Section: 10.1.2.3 32-bit vs. 64-bit Processor Architecture

Practice IM: 10.1.2.4 What Do You Already Know? Choosing a Windows Edition

Practice IM: 10.1.2.5 Check Your Understanding – Choosing an Operating System

Read Section: 10.1.3.1 Checking OS Compatibility

Read Section: 10.1.3.2 Windows OS Upgrades

Read Section: 10.1.3.3 Data Migration

Activity: 10.1.3.4 Check Your Understanding - OS Upgrades

08/31/22 CCNA2
v7.0

 

Discussion: IT Certifications available while at CVCC

Start Chapter 1, Section 5 - Verify Directly Connected Networks

Read Section: 1.5.1 Interface Verification Commands

Read Section: 1.5.2 Verify Interface Status

Read Section: 1.5.3 Verify IPv6 Link Local and Multicast Addresses

Read Section: 1.5.4 Verify Interface Configuration

Read Section: 1.5.5 Verify Routes

Read Section: 1.5.6 Filter Show Command Output

Activity: 1.5.7 Syntax Checker - Filter Show Command Output

Read Section: 1.5.8 Command History Feature

Activity: 1.5.9 Syntax Checker - Command History Features

PT: 1.5.10 Verify Directly Connected Networks

Activity: 1.5.11 Check Your Understanding - Verify Directly Connected Networks

Assignment: Module 1 Study Guide 36-48 (finish)

  A+ Software
v7.0
None today
  IC3

IC3 is a technology certification for non-technology students. Some colleges will award students one credit for certification and students will not need to take an 'Introduction to Technology' course. We will earn this certification because for some this will be the only certification students will graduate with.

https://lms.onlineexpert.com/HeadAdmin/Home/Index
Exam 1: Computer Fundamentals - 33 points
Exam 2: Living Online - 33 points
Exam 3: Computer Applications - 33 points

LearnKey Login Screen Link

09/01/22 CCNA2
v7.0

Start Chapter 1, Section 6 - Module Practice and Quiz

PT: 1.6.1 Implement a Small Network (30 min)

Lab: 1.6.2 Configure Basic Router Settings (30 min)

  A+ Software
v7.0
None today
  IC3

e-library after fire drill

Exam 1: Computer Fundamentals - 33 points

09/02/22

CCNA2
v7.0

Select Class Officers: Pres., V. Pres., Secretary, Treasurer

Finish Lab: 1.6.2 Configure Basic Router Settings

Read/Study: 1.6.3 Summary - What did I learn in this module? Module 1

Practice Module 1 Quiz: Basic Device Configuration

  A+ Software v7.0

Start Section 2 - Storage Device Types

Read: 10.2.1.1 Storage Device Types

Read: 10.2.1.2 Hard Drive Partitioning
Video: MBR and GPT Partition Table (10:41)

Revisit Professor Messer

Activity: 10.2.1.3 Partitions and Logical Drives - Know these terms!!

Activity: 10.2.1.4 Check Your Understanding - Disk Terminology

  IC3

https://lms.onlineexpert.com/Account/Login

Study: LearnKey IC3 GS6: Level 2

09/06/22 CCNA2
v7.0

Video Review: Jason Johnson: Module 1 (33:15)

Test: Chapter 1

  A+ Software v7.0

Read: 10.2.1.5 File Systems

Know the difference between quick and full format

Embedded Video: 10.2.1.6 Disk Management Utility and Disk Partitioning (5:14)

Embedded Video: 10.2.1.7 Multiboot Procedures (3:32)

Lab: 10.2.1.8 Create a Partion in Windows (DO NOT DO AT CVCC)

Lab: 10.3.1.1 Windows Installation Watch Video: Installing Windows 10 on a New PC Build (28:33)
**Install VMWare Player & Windows 10

  IC3

LearnKey IC3 GS6:

Lesson 2: Digital Devices, Connections, and Fundamental Software Concepts